Experimental Measurement and Numerical Simulation of Residual Stress on Butt Welding Steel Plates
-
摘要: 使用压痕法对两副对接试板进行了表面焊接残余应力测试,并通过焊接有限元仿真获得了对接试板焊接残余应力分布规律,对比分析了表面残余应力实测和数值模拟结果。分析结果表明,焊接残余应力数值仿真结果和压痕法实测结果趋势一致,数值相差不大,残余拉应力峰值实测为599 MPa,仿真结果为597 MPa,表明数值模拟方法可预测焊接残余应力;焊缝及热影响区最大纵向残余应力属于拉应力,而最大横向残余应力为压应力,横向残余应力峰值低于纵向残余应力峰值;等效应力(Mises应力)峰值792 MPa,高于试板材料在常温下的初始屈服强度,表明该材料具有明显的加工硬化现象。Abstract: The welding residual stress of two welding steel plates is measured by the impact indentation method, and the residual stress distribution on the butt welding plate is simulated by the finite element method. The residual stress values by measurement and simulation are contrasted and analyzed. The two methods agree well with each other both on the stress value and distribution, The peak value of the residual stress by the actual measurement is 599 MPa, and that by the simulation is 597 MPa, indicating good applicability of the numerical simulation. The longitudinal residual tensile stress near the heat affected zone is larger than that of the horizontal residual compressive stress. In addition, the peak of the equivalent stress (Mises stress) is 792 MPa, higher than the yield stress at room temperature, showing the significant strain-strengthening phenomenon occurs to the material.
-
Key words:
- butt welding plate /
- residual stress /
- impact indentation method /
- numerical simulation
-
[1] 陈冰泉. 船舶及海洋工程结构焊接[M]. 北京:人民交通出版社,2001 [2] WEBSTER G A, EZEILO A N. Residual stress distributions and their influence on fatigue lifetimes[J]. International Journal of Fatigue, 2001, 23:375-383. [3] 中国机械工程学会焊接学会. 焊接手册-第3卷-焊接结构[M]. 北京:机械工业出版社, 1992. [4] 陈怀宁,林泉洪,陈静,等.冲击压痕法测量残余应力中的塑性区问题[J],焊接学报,2001,22(5):21-23 [5] 黄超群, 李桓, 罗传光, 等. 盲孔法与压痕法测量2219铝合金熔焊焊缝残余应力的对比分析[J]. 焊接学报, 2017, 38(7):54-58. [6] 尚伦, 刘冬, 李荣锋, 等. 压痕法残余应力测试系统的设计与应用[J]. 武汉工程职业技术学院学报, 2019, 31(4):41-46. [7] 周科衡, 林超洪, 王超, 等. 盲孔法及压痕法在小湾水电站中的应用[J]. 水力发电, 2009, 35(9):81-83. [8] 王震, 尹越, 李春明, 等. 钢板对接焊接残余应力的数值分析与试验测定[J]. 河北工业大学学报, 2016, 45(4):99-104. [9] GERY D, LONG H, MAROPOULOS P. Effects of we-lding speed, energy input and heat source distribution on temperature variations in butt joint welding[J]. Journal of Materials Processing Technology, 2005, 167(2-3):393-401. [10] 罗广恩, 沈言, 郑远昊. 焊接速度对AH36船用高强钢焊接残余应力及其释放的影响[J]. 船舶工程, 2019, 41(9):104-110. [11] 张青. 焊接顺序对T型接头焊接应力变形和扩散氢数值模拟的影响[D]. 重庆:重庆交通大学, 2018. [12] 沈济超.大型船体结构焊接变形热弹塑性有限元数值模拟方法研究[D].上海:上海交通大学,2015. -
![WeChat](/fileCLKFYYY/journal/article/clkfyyy/2023/2/WECHAT/wechat_cn_0ca4458c-caa3-4a21-b408-108b8ba1e402.jpg)
计量
- 文章访问数: 277
- HTML全文浏览量: 87
- PDF下载量: 96
- 被引次数: 0