High Temperature Creep Properties and Microstructure of Ti-Al-Zr-Mo-Nb-Sn-Si Cast Titanium Alloy
-
摘要: 针对Ti-Al-Zr-Mo-Nb-Sn-Si铸造高温钛合金,研究了其在600℃、750℃下的蠕变性能与组织变化。结果显示,该铸造钛合金在750℃/180 MPa/0.5 h和600℃/400 MPa/0.5 h条件下的蠕变残余伸长率分别<3%和<0.4%,持久断裂时间分别为>2 h和14 h,具有良好的蠕变性能;高温蠕变断口存在细小颗粒;高温蠕变后塑性变形区的组织变化较小,呈魏氏组织,而集中变形区存在部分晶界消失、α片层宽化现象;高温蠕变后位错明显增多,与析出相相互纠缠。Abstract: The creep properties and microstructures of Ti-Al-Zr-Mo-Nb-Sn-Si cast titanium alloy at 600~750 ℃ were studied. The results showed that the creep residual elongations were less than 3% at 750 ℃/180 MPa/0.5 h and less than 0.4% at 600 ℃/400 MPa/0.5 h. The time before creep ruptures were more than 2 h and more than 14 h, respectively. The cast titanium aiioy had good creep resistance. There were fine particles in the high temperature creep fracture surface. After creep, the microstructure changed little in the plastic deformation zone, showing widmannstatten structure, and some grain boundaries disappeared and α lamellae became wider. After high temperature creep, dislocations increased obviously and entangled with precipitates.
-
[1] 许国栋,王桂生,莫畏.钛材生产、加工与应用500问[M].北京:化学工业出版社,2011. [2] 莫畏.钛[M].北京:冶金工业出版社,2008. [3] 朱知寿.我国航空用钛合金技术研究现状及发展[J].航空材料学报,2014,34(4):44-50. [4] 蔡建明,曹春晓.新一代600℃高温钛合金材料的合金设计及应用展望[J].航空材料学报,2014,34(4):27-36. [5] 王清江,刘建荣,杨锐.高温钛合金的现状与前景[J].航空材料学报,2014,34(4):1-26. [6] 刘莹莹,陈子勇,金头男,等.600℃高温钛合金发展现状与展望[J].材料导报,2018,32(11):1863-1869. [7] PRASAD Y V R K,SESHACHARYULU T.Modelling of hot deformation for microstructural control[J].International Materials Reviews,1998,43(6):243-258. [8] 黄永江,蒋香草,沈军.Ti-Al-Sn-Zr-W-Si高温钛合金的蠕变性能[J].材料科学与工艺,2013,21(4):117-122. [9] 张振祺,罗国珍,洪权,等.Ti600合金的性能与显微组织的研究[J].航空材料学报,1999,19(4):6-10. [10] 张振祺,洪权,杨冠军,等.Ti600高温钛合金蠕变前后的组织变化[J].材料工程,2000,28(10):18-21. [11] 王占学.塑性加工金属学[M].北京:冶金工业出版社,1991. [12] 胡青苗.合金化对钛合金力学性能影响的第一原理研究[D].中国科学院金属研究所,2001. [13] 辛社伟,洪权,卢亚锋,等.Ti600高温钛合金中析出物与蠕变性能的关系[J].中国有色金属学报,2010,20(11):2142-2147.
点击查看大图
计量
- 文章访问数: 638
- HTML全文浏览量: 372
- PDF下载量: 21
- 被引次数: 0