Comparison of Properties and Microstructures between Al-Cu-Mg-Ag Alloy and ZL205A Alloy
-
摘要: 采用半连续铸造法分别制备了Al-Cu-Mg-Ag合金与ZL205A合金。对两种铝合金的流动性能、室温及高温拉伸性能、拉伸断口形貌、晶间腐蚀性能和微观组织进行了对比分析。结果表明:浇铸温度为720℃和740℃时,Al-Cu-Mg-Ag合金的流动性能均优于ZL205A合金的。室温、150℃、200℃、250℃下,Al-Cu-Mg-Ag合金的强度均高于ZL205A合金的,且随着温度的升高,其强度降低的幅度要明显低于ZL205A合金的,两种材料的室温伸长率基本相当。Al-Cu-Mg-Ag合金的晶间腐蚀深度在182～246 μm之间,优于ZL205A合金的274～337 μm。Al-Cu-Mg-Ag合金无析出带的宽度要窄于ZL205A合金的。
-
关键词:
- Al-Cu-Mg-Ag /
- ZL205A /
- 流动性能 /
- 晶间腐蚀 /
- 微观组织
Abstract: Al-Cu-Mg-Ag aluminum alloy and ZL205A aluminum alloy are prepared by semi continuous casting. The flow properties, tensile properties at room and high temperatures, tensile fracture morphologies, intergranular corrosion depths and microstructures of the two alloys are compared and analyzed. The results show that when the pouring temperatures are 720℃ and 740℃, the flow properties of Al-Cu-Mg-Ag aluminum alloy are better than those of ZL205A aluminum alloy. At room temperature, 150℃, 200℃ and 250℃, the strengths of Al-Cu-Mg-Ag aluminum alloy are better than those of ZL205A aluminum alloy, and with the increase of temperature, the drop of strength of Al-Cu-Mg-Ag aluminum alloy is slighter than that of 205A aluminum alloy. The room temperature elongations of the two alloys are almost the same. The intergranular corrosion depth of Al-Cu-Mg-Ag aluminum alloy is in the range of 182-246 μm, lower than 274-337 μm of that of the ZL205A aluminum alloy. The width of precipitate free zone of Al-Cu-Mg-Ag aluminum alloy is narrower than that of ZL205A aluminum alloy.-
Key words:
- Al-Cu-Mg-Ag /
- ZL205A /
- flow properties /
- intergranular corrosion /
- microstructure
-
[1] 贾泮江,陈邦峰.ZL205A合金高强优质铸件在大飞机上的应用[J].材料工程, 2009, 37(1):77-80. [2] 刘家军.ZL205A高强铝合金铸件腐蚀行为研究[D].哈尔滨:哈尔滨工业大学, 2014. [3] 黄建余,付永红,穆耀钊,等.ZL205A铝合金微弧氧化研究[J].热加工工艺, 2011, 40(2):131-133. [4] 谭茂林,韩新罡,魏刚,等.ZL205A微弧氧化膜层耐蚀性能研究[J].热加工工艺, 2018, 47(16):144-145. [5] 刘化深,张文兴,白涛.ZL205A铸造铝合金材料在海洋环境下的腐蚀断裂分析[J].热加工工艺, 2017, 46(22):257-260. [6] 王建,王杰芳,郭巧能,等.Al-Cu-Mg-Ag合金热处理工艺的研究进展[J].金属热处理, 2015, 40(3):163-168. [7] 蔡金伶,易丹青,王宏伟,等.Ag对Al-Cu-Mg合金Ω相析出行为的影响[J].中国有色金属学报, 2011, 21(7):1504-1512. [8] 刘晓艳,王召朋,龙亮,等.Mg与Ag含量对Al-Cu-Mg-Ag新型耐热铝合金晶间腐蚀性能的影响[J].材料工程, 2016, 44(9):68-75. [9] 刘海平.Ag、Cu、Mg对Al-Cu-Mg-Ag合金组织与时效硬化行为的影响[D].锦州:辽宁工业大学, 2015. [10] 宋旼,陈康华,黄兰萍.微量Ag对Al-Cu-Mg合金显微组织与力学性能的影响[J].粉末冶金材料科学与工程, 2006, 11(3):159-163. [11] 王建华.2618耐热铝合金的组织与力学性能的研究[D].长沙:中南大学, 2003. [12] 刘志义,李云涛,刘延斌,等.Al-Cu-Mg-Ag合金析出相的研究进展[J].中国有色金属学报, 2007, 17(12):1905-1915. [13] 刘斯琦,屈华,董晓超,等.Al-Cu-Mg-Ag合金强化相价电子结构与热稳定性[J].特种铸造及有色合金, 2013, 33(8):772-775. [14] 齐浩,刘晓艳,梁顺星,等.Al-Cu-Mg-Ag新型耐热铝合金的抗腐蚀性能[J].中国有色金属学报, 2015, 25(11):3033-3039. -
点击查看大图
计量
- 文章访问数: 162
- HTML全文浏览量: 123
- PDF下载量: 11
- 被引次数: 0
下载:
