Ti700sr高温钛合金TIG焊接接头组织及性能研究

梅文佳; 张云浩; 高福洋; 闫飞昊; 余巍; 蒋鹏; 朱乐乐; 刘茵琪

Ti700sr高温钛合金TIG焊接接头组织及性能研究

梅文佳¹,
张云浩¹,
高福洋^1,3,
闫飞昊^1,3,
余巍^1,3,
蒋鹏^1,4,
朱乐乐^2,3,
刘茵琪^2,3

1. 中国船舶重工集团公司第七二五研究所, 河南洛阳 471023;
2. 洛阳双瑞精铸钛业有限公司, 河南洛阳 471023;
3. 国家新材料生产应用示范平台(先进海工与高技术船舶材料), 河南洛阳 471023;
4. 先进钛及钛合金材料技术国家地方联合工程研究中心, 河南洛阳 471023

基金项目:

河南省重点项目资助(3919018001)

详细信息

作者简介:
梅文佳,男,硕士,主要从事有色金属材料组织和性能方面的研究

中图分类号: TG457.1
计量
- 文章访问数: 167
- HTML全文浏览量: 115
- PDF下载量: 9
- 被引次数: 0
出版历程
- 收稿日期: 2020-10-09
- 刊出日期: 2021-08-25

Research on Microstructure and Properties of Ti700sr High-temperature Titanium Alloy TIG Welded Joint

1. Luoyang Ship Material Research Institute, Luoyang 471023, China;
2. Luoyang Sunrui Precision Casting Titanium Co. Ltd., Luoyang 471023, China;
3. National Engineering Research Center for Advanced Titanium and Titanium Alloy Material Technology, Luoyang 471023, China;
4. National New Material Production and Application Demonstration Platform(Advanced Marine Engineering and High-tech Ship Materials), Luoyang 471023, China

摘要

摘要: 采用TIG焊接方法对Ti700sr高温钛合金板材进行了焊接,研究了接头的组织形貌、硬度分布及力学性能。结果表明,Ti700sr高温钛合金板材焊接后的接头成形良好,焊缝区组织由粗大的柱状晶及细长的针状α相构成,热影响区组织由细针状α和残余β相构成,热影响区析出相得到有效控制,相边界上无明显硅化物析出;焊接热影响区的硬度相对较高,焊缝的硬度相对较低;接头室温抗拉强度约为903 MPa, 700℃高温抗拉强度为397 MPa,焊缝强度低于母材的。
- 高温钛合金 /
- TIG焊接 /
- 组织形貌 /
- 力学性能
Abstract: The welding of Ti700sr high-temperature titanium alloy plate was conducted with TIG technology, and the microstructure, hardness distribution and tensile properties of the welded joints were analyzed. It was confirmed that the joint was well formed after welding. The weld zone was composed of coarse columnar crystal and slender acicular α phase, the heated affected zone was composed of slender acicular α phase and residual β phase. The precipitation in HAZ was effectively controlled, and there was no obvious silicide precipitation on the phase boundary. In general, the hardness of HAZ was relatively higher and the hardness of weld low. The strength of the joint was about 903 MPa at room temperature and 397 MPa at 700 ℃. The strength of the weld was lower than that of the base metal.
- high-temperature titanium alloy /
- TIG welding /
- microstructure /
- mechanical property

HTML全文

参考文献(4)

[1]	C.莱茵斯(C.Leyens),M.皮特尔斯(M.Peters)编陈振华等译.钛与钛合金[M].北京:化学工业出版社,2005.
[2]	张翥,王群骄,莫畏.钛的金属学和热处理[M].北京:冶金工业出版社,2009.
[3]	田永武,朱乐乐,李伟东,等.高温钛合金的应用及发展[J].热加工工艺,2020,49(8):17-20.
[4]	王涛.高温钛合金Ti600电子束焊接接头组织及性能研究[D].哈尔滨:哈尔滨工业大学,2016.