Research on Local Corrosion Behavior of High Manganese Austenitic Steel
-
摘要: 采用间浸腐蚀试验、极化曲线测试、扫描观察(SEM)和透射电镜观察(TEM)等方法研究了在3.5%NaCl溶液中添加氧化剂以及敏化处理对低温高锰钢局部腐蚀性能的影响。结果表明:经间浸腐蚀试验后,各试样均主要发生全面非均匀腐蚀,局部可见点腐蚀特征。试样在3.5%NaCl溶液中腐蚀产生的锈层疏松,在3.5%NaCl+0.25%Na2S2O8溶液中腐蚀,试验初期自腐蚀电流密度提高两个数量级,在较短时间内产生致密的锈层,阻止了试验后期腐蚀向内层的快速扩展,试样平均腐蚀速率降低,点腐蚀深度减小。800 ℃×5 h敏化处理后,高锰钢的组织结构没有发生改变,晶界析出了断续分布的碳化物,其抗腐蚀性能与原始态相当,极化曲线印证了这一结果。Abstract: The effects of adding oxidant to 3.5%NaCl solution and sensitization treatment on the local corrosion properties of high manganese steel are studied by using alternate immersion corrosion test, polarization curve test, scanning observation (SEM) and transmission electron microscope observation (TEM). The results show that after the alternate immersion corrosion test, all the samples show the morphologies of overall non-uniform corrosion and local pitting corrosion. The rust layer on the surface of the sample is loose after corrosion in 3.5% NaCl solution. The self-corrosion current density increases by two orders of magnitude in initial stage in 3.5%NaCl+0.25%Na2S2O8 solution, which produces dense rust layer in a short time and prevents corrosion from spreading to the inner layer. The average corrosion rate and the depth of pitting corrosion are reduced. The microstructure of high manganese steel has not changed, carbides precipitated discontinues at the grain boundary after sensitization treatment at 800 ℃ for 5 hours, but the corrosion resistance of the sensitized state is equivalent to that of the original state. The polarization curve confirms the experimental results.
-
[1] 罗晔. POSCO高锰钢产品研发进展及商业化应用[J]. 冶金管理, 2020(16):47-55. [2] 陈晓满, 王玉辉, 王天生. 影响高锰钢力学性能因素的研究综述[J]. 热加工工艺, 2022, 51(4):1-7. [3] 杨跃辉, 梁国俐, 苑少强. 中碳25Mn钢低温冲击断裂过程中的变形机制[J]. 材料热处理学报, 2021, 42(2):98-102. [4] 张鑫宇, 亢淑梅, 杜青林. 液化天然气储罐用高锰钢超低温韧性的提升方法[J]. 河南科技, 2021, 40(1):135-137. [5] 郭伟, 蔡艳, 华学明. LNG用低温高锰钢及其焊接技术发展[J]. 电焊机, 2020, 50(11):7-11. [6] 杜青林, 亢淑梅, 李顺涛. 超低温高锰钢焊接技术发展及在LNG储罐中的应用[J]. 科技创新与应用, 2021(11):40-43. [7] 陈亚魁, 王红鸿, 孟亮, 等. 超低温高锰钢埋弧焊焊缝金属微观组织及冲击韧性分析[J]. 武汉科技大学学报, 2020, 43(5):321-325. [8] 刘帅. 高锰奥氏体孪晶诱发塑性钢的增强增塑及低周疲劳行为研究[D]. 秦皇岛:燕山大学, 2016. [9] 马鹏辉. 高锰奥氏体TWIP钢的循环变形及疲劳裂纹扩展行为研究[D]. 秦皇岛:燕山大学, 2016. [10] BLECK W. New insights into the properties of high-manganese steel[J]. International Journal of Miner-als, Metallurgy and Materials, 2021, 28(5):782-796. [11] LIU Z G, GAO X H, XIONG M, et al. Role of hot rolling procedure and solution treatment process on microstructure, strength and cryogenic toughness of high manganese austenitic steel[J]. Materials Science and Engineering:A, 2021, 807:140881. [12] MISHRA S, DALAI R. A comparative study on the different heat-treatment techniques applied to high manganese steel[J]. Materials Today:Proceedings, 2021, 44:2517-2520. [13] 黄嘉琥. 压力容器用双相不锈钢(二)[J]. 压力容器, 2015, 32(3):1-14. [14] 吕博, 何亚荣, 郑春雷, 等. 纳米高锰钢在海水腐蚀介质中的耐蚀性能研究[J]. 燕山大学学报, 2016, 40(1):9-15. [15] 王保成. 材料腐蚀与防护[M]. 北京:北京大学出版社, 2012. -
点击查看大图
计量
- 文章访问数: 82
- HTML全文浏览量: 20
- PDF下载量: 14
- 被引次数: 0
下载:
