U型镍钛合金丝热定型及力学性能分析

邹轶乐; 高超

U型镍钛合金丝热定型及力学性能分析

邹轶乐¹,
高超²

1. 江苏科技大学机械工程学院, 江苏镇江 212100;
2. 常熟理工学院机械工程学院, 江苏苏州 215500

详细信息

作者简介:
邹轶乐,男,1997年生,硕士研究生,主要研究方向为镍钛合金热处理。E-mail:69427780@qq.com

中图分类号: TG139.6
计量
- 文章访问数: 326
- HTML全文浏览量: 64
- PDF下载量: 47
- 被引次数: 0
出版历程
- 收稿日期: 2021-09-28
- 网络出版日期: 2022-06-11

Heat Setting and Mechanical Property Analysis of U-shaped Nickel-titanium Alloy Wire

ZOU Yi-le¹,
GAO Chao²

1. School of Mechanical Engineering, Jiangsu University of Science and Technology, Zhenjiang 212003, China;
2. School of Mechanical Engineering, Changshu Institute of Technology, Suzhou 215500, China

摘要

摘要: 采用不同的加热条件对镍钛合金丝进行定型,研究镍钛合金丝的力学性能及内部组织结构,确定了镍钛合金丝的最优热定型工艺参数。使用拉伸所用强力仪对镍钛丝进行拉伸性能测试,使用光学金相显微镜对镍钛丝进行金相组织观察。结果表明,热定型温度越高,加热时间越长,镍钛丝热定型效果越好,镍钛丝尺寸越接近定型模具尺寸;镍钛丝上下平台应力随加热时间的增加变小,其中,加工条件为550℃、20 min的上下平台应力最小,残余应变在加热时间多于10 min时显著增加;随着温度和加热时间的增加,镍钛丝内部奥氏体组织分布越来越均匀,奥氏体晶界越来越明显,其组织晶粒平均尺寸也越来越大。
- 镍钛合金丝 /
- 热定型 /
- 力学性能 /
- 金相组织
Abstract: Different heating conditions are applied to shape the nickel-titanium alloy wires, the mechanical properties and internal structure of the nickel-titanium alloy wires are studied, and the optimal heat setting process parameters for the nickel-titanium alloy wires are determined. The tensile properties of Ni-Ti wires are tested by tensile tester. The metallographic structure of the Ni-Ti wire is observed by optical metallographic microscope. The results show that the higher the heat setting temperature and the longer the heating time, the better the heat setting effect of the Ni-Ti wire and the closer the size of Ni-Ti wire to that of the setting die. The stresses of the top and the bottom plateaus of Ni-Ti wire decrease over the heating time, and when the temperature is 550℃ and the heating time is 20 min, the stresses of the top and the bottom plateaus are the smallest. The residual strain increases significantly when the heating time is more than 10 min. With the increase of the temperature and the heating time, the distribution of austenite structure in Ni-Ti wire is more uniform, the austenite grain boundary becomes more obvious, and the average grain size of the structure becomes larger.
- Ni-Ti alloy wire /
- heat setting /
- mechanical property /
- metallurgical structure

HTML全文

参考文献(11)

[1]	邹秋华.一体化编织型血管支架的制备与力学性能研究[D].上海:东华大学,2016.
[2]	阎小军,杨大智,刘黎明.超弹性NiTi合金丝激光点焊接头的组织和性能[J].中国有色金属学报,2005,15(1):19-23.
[3]	樊亚军,张战英,陈志宏,等.纯钛等温加热过程中再结晶晶粒生长行为[J].材料热处理学报,2013,34(S1):22-25.
[4]	王璐,邹秋华,林婧,等.一种编织型一体成型血管覆膜支架及其制备方法:CN104689379A[P].2015-06-10.
[5]	赵石磊,赵昆,王富文.NiTi基形状记忆合金相变温度的影响因素[J].有色金属工程,2021,11(2):38-47.
[6]	高静,杨冠军,杨宏进,等.热处理对医用TiNi细丝显微组织及形状记忆效应的影响[J].稀有金属材料与工程,2005,34(2):299-302.
[7]	刘晓鹏.NiTi形状记忆合金的超弹性及医学应用研究[D].大连:大连理工大学,2008.
[8]	黄兵民,郑玉峰,蔡伟,等.冷变形TiNi合金的显微组织及超弹性[J].宇航材料工艺,1997,27(6):51-54.
[9]	袁志山,吴艳华,周瑾,等.钛镍形状记忆合金丝材力学性能研究[J].热加工工艺,2014,43(14):183-186.
[10]	熊雯瑛.冷变形及热处理对Ti50Ni50-xCux合金组织与性能的影响[D].长沙:中南大学,2013.
[11]	于孟,贾兵然,薛飒,等.钛镍形状记忆合金加热过程中的晶粒长大行为[J].热加工工艺,2017,46(22):238-241.